Mounting NFS with /etc/fstab and NFS mount Options
Mounting NFS with /etc/fstab
An alternate way to mount an NFS share from another machine is to add a line to the /etc/fstab
file. The line must state the hostname of the NFS server, the directory on the server being exported, and the directory on the local machine where the NFS share is to be mounted. You must be root to modify the /etc/fstab
file.
...
server:/usr/local/pub /pub nfs rsize=8192,wsize=8192,timeo=14,intr
The mount point /pub
must exist on the client machine before this command can be executed. After adding this line to /etc/fstab
on the client system, type the command mount /pub
at a shell prompt, and the mount point /pub
is mounted from the server.
...
<server>
:</remote/export>
</local/directory>
<nfs-type>
<options>
0 0
Replace
with the hostname, IP address, or fully qualified domain name of the server exporting the file system.<server>
...
Replace
with either <nfs-type>
nfs
for NFSv2 or NFSv3 servers, or nfs4
for NFSv4 servers.
Common NFS Mount Options
Beyond mounting a file system via NFS on a remote host, other options can be specified at the time of the mount to make it easier to use. These options can be used with manual mount commands, /etc/fstab settings, and autofs.
...
fsid=num — Forces the file handle and file attributes settings on the wire to be num, instead of a number derived from the major and minor number of the block device on the mounted file system. The value 0 has special meaning when used with NFSv4. NFSv4 has a concept of a root of the overall exported file system. The export point exported with fsid=0 is used as this root.
hard or soft — Specifies whether the program using a file via an NFS connection should stop and wait (hard) for the server to come back online, if the host serving the exported file system is unavailable, or if it should report an error (soft).
If hard is specified, the user cannot terminate the process waiting for the NFS communication to resume unless the intr option is also specified.
If soft is specified, the user can set an additional timeo=<value> option, where <value> specifies the number of seconds to pass before the error is reported.
...
Note
Using soft mounts is not recommended as they can generate I/O errors in very congested networks or when using a very busy server.
intr — Allows NFS requests to be interrupted if the server goes down or cannot be reached.
nfsvers=2 or nfsvers=3 — Specifies which version of the NFS protocol to use. This is useful for hosts that run multiple NFS servers. If no version is specified, NFS uses the highest supported version by the kernel and mount command. This option is not supported with NFSv4 and should not be used.
noacl — Turns off all ACL processing. This may be needed when interfacing with older versions of Red Hat Enterprise Linux, Red Hat Linux, or Solaris, since the most recent ACL technology is not compatible with older systems.
nolock — Disables file locking. This setting is occasionally required when connecting to older NFS servers.
noexec — Prevents execution of binaries on mounted file systems. This is useful if the system is mounting a non-Linux file system via NFS containing incompatible binaries.
nosuid — Disables set-user-identifier or set-group-identifier bits. This prevents remote users from gaining higher privileges by running a setuid program.
port=num — Specifies the numeric value of the NFS server port. If num is 0 (the default), then mount queries the remote host's portmapper for the port number to use. If the remote host's NFS daemon is not registered with its portmapper, the standard NFS port number of TCP 2049 is used instead.
rsize=num and wsize=num — These settings speed up NFS communication for reads (rsize) and writes (wsize) by setting a larger data block size, in bytes, to be transferred at one time. Be careful when changing these values; some older Linux kernels and network cards do not work well with larger block sizes. For NFSv2 or NFSv3, the default values for both parameters is set to 8192. For NFSv4, the default values for both parameters is set to 32768.
sec=mode — Specifies the type of security to utilize when authenticating an NFS connection.
sec=sys is the default setting, which uses local UNIX UIDs and GIDs by means of AUTH_SYS to authenticate NFS operations.
sec=krb5 uses Kerberos V5 instead of local UNIX UIDs and GIDs to authenticate users.
sec=krb5i uses Kerberos V5 for user authentication and performs integrity checking of NFS operations using secure checksums to prevent data tampering.
sec=krb5p uses Kerberos V5 for user authentication, integrity checking, and encrypts NFS traffic to prevent traffic sniffing. This is the most secure setting, but it also has the most performance overhead involved.
tcp — Specifies for the NFS mount to use the TCP protocol.
udp — Specifies for the NFS mount to use the UDP protocol.